Dec 2013

Well things have started to move along. I have just spent the weekend working on the car and have achieved a bit really, much thanks to my dad for giving me a hand with some of it. So far I have managed to replace the axel to hub seals and the back brakes, slave cylinders and pads and two of the three flexible hoses. The master cylinder was changed over in a surprisingly short space of time (thankfully), though I have noticed that the new master cylinder cap does not actually have a breather hole in it, so not sure if it should or not. The old cap definitely has a breather hole in it and to be honest I had never known that it was supposed to be there, it was so perfectly filled with dirt that you could not even see where it was supposed to be (don’t get me wrong the cap was perfectly cleaned and wired brushed of all dirt, it was just that not knowing the hole was supposed to be there I had never even noticed that it was full of dirt). I had never been able to get the brakes to bleed properly and it was a constant round of bleeding and re-bleeding every few months to try and get some pressure, usually I actually had to pump the brakes up to use them at all. Once I knew there was supposed to be a breather hole and I found the location and cleaned it out, BAM! the brakes bled and pumped up perfectly with a fantastic pressure, it was amazing.

 

The front brakes are being somewhat of a pain, I managed to get time to replace the cylinders and fit the new shoes/pads but the drum then flatly refused to go back onto the hub. It is as though the brake shoes are holding it so far out of alignment as to not have any way of getting the drum on. Dad managed to move the shoes with a screw driver whilst trying to get the drum on and managed to get it to fit, though there was no hope what –so-ever of getting the hub to then turn, it had locked up so tight that it too judicial thumps with a rubber mallet to get it off again. So the wash up of that is we’re going to get a mechanic to come and have a look at it just to see what the devil is going on there and whilst he is there get him to bleed the system as well, saves me doing it. 

Additionally have replaced the water pump, radiator and radiator hoses and the thermostat and housing and the by pass hose as well. I will need to get some new heater hosing and replace the fuel hosing as well as rubber components don’t like the hot humid weather where the car is locate at the moment, so just to be sure they need renewing. 

The new radiator is quite different to the original one I had in the car in that it doesn’t have the high top tank and it also does not have the drain tap and the bottom drain plug either. This is most vexing as I have had the heater hose running off a brass fitting in the bottom drain plug and now I have to come up with the correct piping and such for the later cars so that I can refit the heather hoses properly. Further I am going to have to find a way of modifying/adjusting the lower two mounts for the radiator as the new one sits about 1mm from the fan blade at the bottom, the top there is no problem at all for clearance, and 1mm clearance is just not enough the run safely with out the fan cutting a nasty hole in the radiator. Hmmm maybe a thermatic fan is necessary after all? 

 The new tyres are all fitted and looking quite good on the rims, they don’t look at all out of place I think and fit quite nicely. The fitter was most certain that I had to have inner tubes fitted as well with these tyres so luckily I had managed to get a bunch of new tubes and supplied them as well as the rims to the fitter. The tyres are the Nankang 155/80 R14 type and where not badly priced and look a whole lot better than the old crossply ones did. Mind I did have one reasonably decent crossply amongst the ones on the car and I have kept that to have it mounted on the spare rim as the Nankang won’t fit into the spare spot, so it will have to be my “emergency” tyre just like a modern has. Anyway progress has been made and now it is just a matter of getting the brakes seen to properly and then driving the car down to Melbourne for some proper going over and fitting of a few electrical items to make it comfortably able to cope with the modern sound and electrical requirements and then get it registered. Thank goodness I fitted an alternator all those years ago!

November Part 2

Well the good news is that I am off to visit the family for a long weekend at the start of December and as such that will involve being in the same place as the Count for the same length of time. Whilst I know that it really isn’t all that long of a break, as I don’t sleep much and as there is electricity in the garage (read: this means there are lights as opposed to the single dim bulb in the machinery shed it used to reside in!) so I should be able to get some decent family time in and also get some work done on the car as well. 

 So far I have the wheels booked in for new set of Nankang 155/80 R14 on the Saturday, so I will have to find/borrow/hire 4 axel stands so that I can get all the wheels off at once to get them into the tyre shop. I have also sourced and should have in the next couple of days the correct (so I am told) type of inner tube to install in the tyres, as the original Morris rims don’t have a beaded edge to seal the radial tyres against properly. 

Further I have purchased a brand spanking new radiator that should be on it’s was to location by Friday this week so will be waiting ready when I get there. Plan of attack will then have to be get a level to check if the wheels are straight or if they are toe-ing in, then get the Count onto the 4 axel stands and all the wheels off and cleaned up a wee bit so they aren’t too messy for the installation of tyres on Saturday morning. While the wheels are all off, if necessary, install the spacing washers on the eye bolt to true the wheels back to straight. Then it is replace all of the brake slaves, front and back, and the master cylinder, fill and bleed the system and adjust the hand brake and refit the wheels. Next is to drain the coolant, flush some fresh water through the system and whip the old radiator out and while I am at it and as I have a new one, remove and replace the water pump, drop a new fan belt in and then fit the new radiator. 

At this stage best bet will be to remove the heater core and also remove the 1000/Mini heater tap, flush through the heater core and if it is ok refit (if not ok then bypass till later), mount the correct type brass screw heater tap and then fill with coolant. From that point it will be best to fit the new locking petrol cap, which is a shame as I like the wee chrome original cap, fill the petrol tank with fresh fuel and then I should be well out of time and be on a flight back home. 

I think I will take the voltmeter with me so that I can see that the alternator is still producing power and I will need to make sure all the lights are working and shining and flashing as they need to be. The current train of thought is that I will head beck to Queensland later in January (due to school holidays and high airfares) and then I will drive the Count back to Melbourne, via the Wide Bay - Burnett, Newell, Olympic and Hume highways, already comprehensively insured as it will be, with a unregistered vehicle permit and compulsory third party. 

I am sure it will be interesting to see (1) if the car makes it, though I see no reason why it wouldn’t, (2) how many times I get pulled over for not having any number plates, hopefully none. I guess one thing I should not have to worry about is getting stopped for speeding! As a result of all this there will be pictures to follow of the work done and then of the trip down to Melbourne in the relatively near future. Actually quite looking forward to getting some work done and getting the car down to Melbourne, finally going to be getting somewhere with it and getting it ready for it’s trip around Australia.

Hopefully will be back to looking this good in the near future

Nov 2013

So starts November and still more delays getting my hands on the car. Looks like there is no doubt now, the Count won't be in Melbourne this year, it is going to be late January or early February before it appears in town, actually may have to consider waiting until the kids go back to school after the christmas break just so there won't be so much traffic on the roads, thus the mention of February, very tiresome as I want it here now! It is hardly fair I think really, but our trip to Europe and then my parents European cruise have not left great amounts of time available between now and christmas / end of year to be able to head up north and sort things out, such trials haha. I am visiting though in early December and as such will be able to get some work done, though probably limited for a short visit. 

There is quite a deal of small fiddly things that need to be done before I can get it running and one of the first items has to be the brakes, if for nothing else other than that the garage is at the top of a quite steep driveway and there is no chance that the car can leave the garage unless the brakes work. So on this December visit I have to take such parts as are necessary to ensure I can get it running, any of the nice to have parts can stay in Melbourne to be fitted / replaced once the car is down here. I am going to have to sort out the front wheel geometry as I have said before I don't want to be destroying a set of new tyres just getting back to Melbourne (27 hour drive from my parents house!) as they will certainly scrub out over the return distance otherwise. 

I have been in contact with a local tyre seller, well local to where the car is currently, and everything seemed good as he had found the inner tubes I will need are available, though I have not heard from him in a couple of weeks so I must chase that up and see if he can supply and fit tyres as well. I will be getting the Nankang CX-668 Tourer 155/80R14 81T, and yes I know that 145/80/14 would be a much better option, but they just aren't available in that size here in Australia, well not anywhere that can locate anyway, and I don't want "antique" items. The 155 are only 10mm wider than the 145 and if they are maintained and the pressures checked regularly they should be just the ticket. If he can't supply the tyres as well as the tubes then I will just get the tyres direct from a supplier on the internet and then see if he will fit the tyres and tubes for a reasonable price, hopefully all will work to satisfaction. 

Items I have to replace that I can think of at the moment are: Master Cylinder Front and Rear Slave Cylinders,  Front and Rear Brake Shoes, Flexible Brake Lines, Radiator, Heater and Fuel Rubber Hoses, Water-pump, Thermostat Housing and Thermostat. 

I think that is the total of the absolutely must do items, that I currently have, just to get it ready for the trip to Melbourne, so as such hopefully I will be able to get that done in December. Further I still need to decide on what I am going to be doing in relation to the radiator, it has to definitely have something done as it is just past its best really. I have had a quote from a reconditioner and the price could be either $350ish or $450ish, depending on what type of core my radiator has. It seems that the Radiator man has been informed by his supplier that there are two different types of core used in the Morris Minor (really? there are?) and until the core is removed and measured up he can't tell which it would be. If this is so you can bet without shadow of a doubt that mine would be the most expensive kind as most anything always seem to be so if there is a cheaper option available. That being said I can also buy a brand new radiator to just drop straight in and bolt up and not even have to worry about it at all having old top and bottom tanks, that would cost more though technically it would be the best option I think, mind brand new isn't a guarantee of quality and longevity is it! The brand new beastie would cost $500ish but to be honest given the approximate quotes for the re-core it would probably be better to spend just that bit more and get new, radiator bling, haha! 

I am also still throwing around ideas about the gear box, I have found some very helpful people that quotes me about $660 to recondition a box for me, using a later 948 box, though then taking the remote leave housing off the box and fitting the earlier 803 box tail. This of course would require them to swap the reverse gear selector rod so there is a lock out as a straight swap out with out changing the selector rod means that reverse would be able to be selected at anytime due to differing lock out systems between the two boxes. I think it would not be necessary to swap the 803 speedo drive with the 948 one in the 948 box as the car currently has a 948 speedo in it and it doesn't read correctly with the 803 box anyway. Maybe this all need some more thought and advice from the rebuilders. I'll have to get back to you on that I think....

Back when it was on the farm, keeping the Humber company

Sep - Oct 2013

Ok sorry to anyone that regularly reads this (if anyone regularly, or otherwise, reads this at all) for the delay in posting updates. I have been away on holidays and have not had access to a computer for the last 5 weeks, which has been great! 

Holidays were in Europe, and went to the Goodwood Revival, Frankfurt Motor Show, Classic Remise in Berlin , Haynes Motor Museum , Beaulieau Autojumble, and various other places and locations, not all car related I must add. Goodwood was, as previously just really quite fantastic, the racing was great, the Spitfires brilliant and the atmosphere as always fun and relaxed. It is great to see so many people getting into the vintage spirit of the event and dressing for the occasion. The car park alone is almost worth the visit by itself, such a amazing array of vehicles parked in the paddock. It is great to see that people are happy to use cars that are worth such vast sums and not just leave them locked in a shed. Over all Goodwood Revival is a great event and it really has grown in size quite noticeably since the last visit to it a few years ago. No wonder it is a sell out every year. 

The Frankfurt Motor show was just out of this world, it really makes the old Melbourne and Sydney “International” motor shows look quite tragic and tiny by comparison! To be honest the old Sydney or Melbourne shows would quite easily have been accommodated in just the Mercedes pavilion alone at Frankfurt , and quite comfortably at that! The scale of the pavilions and variety of cars and parts suppliers on show was truly overwhelming. Really such an amazing spectacle and the amount of money they must have to spend to present it is really quite mind blowing. Whilst we didn’t get into the Audi pavilion the Mercedes on was by far the stand out in style and scale. 

A recommendation for Berlin, make the effort to go and see the Classic Remise, which of course is moving to a new home in 2015 I believe, the current building (an old imperial tram depot) and setup is really quite something and the range of cars that are there being stored or waiting for sale is just amazing. Really like the two Horch 853A Sportroadsters which would have to be a personal favourite. Whilst travelling about the UK in our rented bright red Fiat 500 (what a great little car!) was trying to decide if I should look up and visit a few Morris Minor parts places prior to going to the Beaulieau Autojumble or not, as maybe all that I wanted would be at the Beaulieau and “special” prices, but in the end decided to visit Bull Motif Spares in Winchcombe, Gloucestershire. I purchased quite a few parts and bits most of which I managed to pack into my luggage and some larger parts that I had mailed home. I was very glad that I had stopped by Bull Motif as, maybe I wasn’t looking carefully, but I didn’t see many Morris Minor parts at Beaulieau at all, and no specialist suppliers that I saw. I had though that as Beaulieau was such a big event and grandly advertise as being an International Autojumble that there would have been a great many traders of Morris Minor parts, so that was a insight to the event. Don’t get me wrong it was great to attend and see what this event I have heard so much about over the years was actually like and there were a vast number of traders and private sellers, and it was definitely international, so many Dutch nationals, both selling and buying, they must really like the British cars. Mind one question remains, clogs, really, you actually wear them, surely they can’t be at all comfortable walking for miles through wet and muddy grass! There was so much “stuff” at the Autojumble that it would be almost impossible to actually take everything in, there was certainly some amazing items and I think it would be hard to locate the exact obscure part your after without actually scouring each and every stand, though what your after is probably there somewhere. Well not so much Morris Minor spares, but plenty of other stuff anyway. 

So anyway heaps of bits and pieces for The Count, which should have it looking and running mighty fine for a while. Thus now it is the hard slog of saving the money for the actual trip and figuring out when I can actually get to the car and install the parts that are needed to get it road safe and legal, so that I can then either just drive the car from Queensland to Melbourne or have it freighted. I have been looking at freighting it and it has to be fully operational and running for that, so with the brakes needing doing and such like that I may as well just drive it down once it is all done I think, well that is what I would prefer to do. 

Well hopefully now I have all of these parts, one day in the not too distant future I will be able to get to the car and start to sort it all out, I would like to be able to get it down to Melbourne prior to Christmas, though this may slip a little to early in the new year, I hope not, though as there is only 11 weeks to go until Christmas it may just catch me out.

Goodwood Revival parking lot

The mighty 500 in the UK

August 2013

Well have just been looking through some photos that I forgot I had and well here are a couple of The Count preparing for the journey from the farm to the new garage and of the car in residence at the new place.

Funny how you forget about taking some pictures until you start looking isn’t it. Thank goodness for the 4x4 because the weight of that trailer alone was staggering. The only reason that the car was trailered and not driven is that the master cylinder had given up the will to operate (probably the seals) and as I have not obtained a new one yet to replace it with it was an impossibility to drive down the highway and across town. Completely aside from the fact that the radiator needs a recore still and would have overheated by the time it got to the end of the drive, well maybe an exaggeration though I am sure it would not have made it too far before it did. 

Plans are afoot to get hold of some much needed parts in the near future, though actually getting time to fit them and start the process of getting The Count roadworthy again is seeming hard to nail down, maybe around December I will actually get to start, depending on funds and leave availability. I need to source a master cylinder and brake shoes front and rear, a complete set of hoses, rear window seal, horns that actually make a noise, water pump and a new thermostat housing and the outlet on the old one has been eaten away. Of course there are other items too like gaskets and exhaust hangers and flange clamps and such, but the main parts are just to get it running rather than required “spare” parts. 

I hear that the International Autojumble at Beaulieu in the UK is Europe ’s biggest and as it is a British car I reckon that I need to see about visiting there one day, maybe, one day anyway. 

 I’ve been working out a few wiring diagrams to get my head around what I need to do so as to install the necessary upgrades as well. The car already has a alternator fitted so that is a start, but I need to sort out fitting relays into the system in a few places so that I can run halogen lights without melting down the original switch with the extra current load which would be nice. I also want to have the trafficators working again (they probably just need a good service after sitting so long, I’ve had them working before) and I want them working along side the indicators and all controlled by the one switch, so I have been thinking about that as well and I think that along with a couple of relays I will be able to sort that relatively easily too. Oh well back to planning, not long now till until it all starts to happen, really looking forward to that!

July 2013

Not really sure that much has been going on at all though I guess plans change and improve and things are really starting to come together with the planning. I think I have finally figured out the route that I want to take and that lands to knowing the proposed total mileage just to get between those points, It also lets me plan on how long it will take in hours to travel between those points so I guess I can also start planning on where I will be looking at staying after the particularly long runs. 

Of course once I get the car home a great deal will change and work will be able to commence properly, though by that time all of the planning should be complete and it will just be the mechanical side of things to progress with. I have managed to find a place that does tyres of the type I am looking for at a decent price, so I am pleased that I have located that and I have something to compare all the other tyre sellers to now. So if prices are to madly expensive I can always get them from this company I have found and then just have them and new inner tubes fitted to the rims at any tyre place which should cost less. Mind I would have to pay to get rid of the old ones as well so that is another cost factor to remember in the comparison costs. I have to additionally sort out the problem with the mysterious one side scrubbing out the inner edge of the front tyres and then once it is replaced the other side has a turn. Not sure why it is doing this it certainly is most odd I can understand one side doing it continuously, but swapping from one side to the other is a concern. 

Hopefully the trunions aren’t worn out too. I have to say though that I have recently been re-reading some of my Morris Minor books and old Morris Minor Owners Club magazines and the old Morris Minor magazine “Minor Monthly”, and reading about the methods of setting up the wheel alignment on the Morrie which has brought on a very vague recollection. When I was replacing all of the old original rubber suspension bushes etc in The Count, some years ago now, with polyurethane ones I have the very slightest of ideas that when I took the eye bolts out of the chassis legs I may have removed the spacer washers whilst thinking to myself “why the hell would you put a washer on this side of the chassis leg”. As I say I very vaguely recall that and it will be interesting to check if it is so once I go and visit the car again to start replacing all the brake parts. I am hoping that this is the case and I have simply to replace the washers and all will be good with the geometry again. It would after all be great not to scrub the inside edge out of a brand new tyre straight away, let alone at all, I think! 

 Oh and the tyres, well I know it is non-purest, but after so many years with antique and out of date cross-ply tyres I want new belted radials, obviously with inner tubes inside them. Perhaps the handling will be better, maybe, though lets face it the handling is great anyway, it is a Morris Minor after all, what I am hoping for though is a reduction in road noise. Let’s face it the last “new” set of cross-ply tyres I put on the car (well they are actually still on it now) was quite a long time ago and yes they were starting to get a bit thin on the tread, they were well past the mandatory replacement age of 5 years old when I actually bought then “new”. 

Sadly we don’t have the European laws relating to tyre age in Australia and they are legally permitted to sell "new" tyres that could be well over 10 years old before they ever see life on a vehicle at all. The old rubber hardens and whilst they still do the job reasonably well they also transmit a heck of a lot of road noise into the cabin. So I am hoping that new tyres that are guaranteed less than 12 months old from date of manufacture, and being not cross-ply, will bring a whole new level of noise buffering as well as better grip and comfort. We shall see I guess...

June 2013 pt 2 - Current Planned Route

Well I have been working through some maps and web sites and have decided on the third planned route so far this year, so it will probably change yet again, though it would be great to be able to go with this one as it covers areas mostly that I have not seen before, rather than travelling over roads that I have already done in the past (admittedly not necessarily in The Count though). I have checked out a few forum groups and some other information on the web and it seems that all the routes I have decided on so far are actually fairly much all sealed roads, besides people tow caravans over the roads so I think a Morris Minor should be able to make it as well. This is the proposed route

(sorry the quality is not the greatest, will have to try another scanner and replace it later if it works better) Currently the total distance works out to be approximately 24,061 kilometres (14,950 miles) and it includes some back tracking points, but worth it for the experience and seeing lots of "otherwise never going to get there" places. Given that it is possible to try and figure out what it will cost in fuel and such working with a few random guestimated input data, thus: Supposing that The Count has a 22 litre tank and that it is running at 8 litres/100 kilometres and that fuel is averaged at 172cents/litre it would be working out at: Total Litres - 1925 No: of Tanks - 87.49 Cost - $3,272.00 AUD So given that I can play around and come up with various figures that range from a cost of $2,695 to $6,256 for that cost of fuel for the whole trip by varying the average fuel consumption and the cost of fuel at cents/litre. Certainly is an interesting exercise

June 2013

Well here we go, not much at all has been happening, though have spent some time reviewing the planned route and where I want to go and see. With a better idea of where I want to go this has led to a revision of the distances to be covered and even to a proposed projection of what the fuel for the trip may cost. Give the variable cost of fuel I have worked it out at various cents per litre amounts just to see what I should be budgeting for, surprisingly it isn’t actually too bad (well from this end of the trip anyway) so that is something. I have redrawn the line around Australia and through the north south middle that will be the proposed route and have come up with a new total distance to drive just the trip as planned of 21,725 kilometres, so that is only 13,500 (ish) miles. 

Have to say the kilometres total does sound more impressive, though as the speedo is in miles I guess its best to have both figures. The speedo will require a re-calibration though as it only reads about half the actual speed and as such the “mileometer” is well out unfortunately. This distance of course doesn’t include any “off route excursions” so it is just a general guide, though I have amended the route plan to include getting too and from Uluru and going to Longreach as well. Oh and down to Port Lincoln rather then just taking the direct route to Adelaide from the Nullarbor. I am sure though I have not added even half of the things and places will end up wanting to see and do, thus there is no doubt the distance and fuel cost will climb.

 I have also been looking at how to get The Count down to Melbourne and been pricing having it freighted, the costs for which vary and it is between $650 and about $1650 with various companies. Some figures will permit the car alone, not carrying anything inside it and some will allow items to be in the car. There is of course the option to get a vehicle permit and drive The Count down to Melbourne, which isn’t a mad as it sounds as I have to have the car running and brakes working etc before it could be freighted, so why not drive it anyway and it can be a shake down trip for the drive to follow. I have of course got top level breakdown cover with the motoring organisation and they assure me it will cover me for any vehicle I am driving so that is good if it works. 

I would prefer to drive it down to Melbourne myself as it is much more interesting a prospect that loading it onto a truck and waiting for it to arrive at the other end. Time will tell I guess, one needs to be able to get insurance cover for it first or it won’t be driven anywhere and with it not actually being registered yet that can be a hassle for a permit drive of such long distance (across three States, all with different police forces and vehicle registry authorities!). Anyway time will tell. 

 I was actually looking into registration in Victoria and what rego plates I may be able to get on the car. Since Victoria had started to issue plates commencing with a “Y” I was actually hoping that I may actually be able to get the “Victoria” version of the plate The Count used to have when it was registered in the ACT. Back in the day all of the States had a block of letters that registration plates in their territory could start with and the ACT had “Y”, so if you saw a plate that started with the letter “Y” you knew it was a vehicle registered in the ACT, which made things so easy. 

Now those rules have changed and all of the States seem to be going off in all directions relating to rego plates, which is not a bad thing, though it would have been good if my old ACT number was still available in Victoria. Doesn’t matter though, it isn’t as though it was a special number, it is just the first number it had from the time I owned it, just a bit of nostalgia. Victoria now has a whole range of different types of plates available, as well as the old standard size, so I will have a look through those and see what is available. Hmm maybe some euro style plates would be the go, at least they should fit into the plate mounting on the boot lid, unlike the standard type plate…

May 2013

Oh well here we go, another month and things progress slowly.

Going back to last month I have passed up on getting a gearbox and will probably just aim at getting the original reconditioned once the car is here and I am at the rebuilding stage. It’s the original so it may as well stay in the car, and yes true there is so much that has been changed already for later model and other parts it’s probably silly, but what the heck I have it and know it, so it may as well stay. To be honest I probably don’t need to do anything to it to be able to undertake such a drive, though with the jumping out of third under acceleration being annoying….

On the radio front I am mostly looking towards the Oricom UHF300 5W UHF 80 ch. mobile transceiver, though not really sure. I don’t need something with all the bells and whistles as it isn’t like I will use it constantly, it is only a just in case measure (as in just in case a massive road train needs to let me know it is about to run over me) so realistically it just needs to do the job. Thus mainly I am being driven by price, though I am reading reviews of different units from different suppliers and will continue to compare then to identify which one will work best for me. Space is also an issue and being small and easily able to mount it out of view so as to not spoil the interior look would be good. I have toyed with the idea of getting a hand held item as it would certainly be easier to pack away and would definitely be portable, I just think that mounted in the car will be less hassle and more practical and possibly have a slightly better range, though I may be mistaken on that.

I have lately been looking through a variety of sources of information on places to pitch a tent and camp along the routes I plan on taking. It is amazing just how many different resources there are out there that you never hear about, unless you actually start looking, though I guess that is true with just about any subject. There are a number publications that look particularly interesting to me , I am looking at WikiCamps Australia , which is an app (there is one for everything isn’t there!) at the moment that looks like it would be fairly useful. I have also found out about “Camps Australia Wide”, Version 7 (http://www.campsaustraliawide.com/ )   which looks like the best source of information for me, free and budget accommodation that’s just the price range I will be looking for, so that looks like it will be quite the useful investment indeed. Not that I plan on only looking for free accommodation places, I have a Youth Hostel Association membership as well which will no doubt come in handy.

On the car front, well it is still not in Melbourne so everything is still limited towards actual hands on processes. Sometimes it feels like there is only so much planning that I could possibly do and that everything has been covered, then something else will crop up and get me to thinking again. This is probably a good thing really as it would be quite tiresome to get part way through the trip and suddenly be in need of, or wanting something that could have been available if only a bit more thought had gone into the process of planning. It’s not that such a situation isn’t likely to occur anyway, but it is nice to think everything has actually been covered before hand.

I have been fine tuning the lists of items that I think  the car will need, hoses, brakes, head gasket and the like, that will need to be done before the trip can start and additionally the list of items that I will need to take as spares. Further I have a list of items that I will need to take along, tent, cooking stuff, etc. and a list of tools that will be useful to have, lets face it there is no point taking tools I don’t have any hope of using and no point not taking tools that I know I can use and may actually be useful. So I check them every now and again and add items and then take some away, what I actually would like to achieve is being able to fit everything into the boot as that is the tidiest and most practical way to be getting along I think.

Down on the farm

April 2013

Ok so having seen a reconditioned 1000 gearbox on e-bay for a good price I am now back to wondering what to do with The Count.
The Count still has the original box in it and it has never been opened up, worked on, etc. since I have owned it, and it is seriously going to need to be looked at before the trip. The car started jumping out of third under acceleration quite some time ago, though it doesn't really throw the lever out in any really forceful way so it is easy to hold it there before changing to forth, and it is somewhat of a noisy thing too. It doesn't make any unusual sounds though it is more just that it has been doing the job for a fair amount of time now and it could use a recondition.

That is the point of the deliberations about the situation, do I pay over $1000 to have the gearbox reconditioned, being original the to the car 803 box with the three foot direct shift lever, do I just get another second hand 803 box, do I get a second hand 1000 box or do I get a reconditioned 1000 and then just change the gearbox cover for the 1000 item and change the handbrake lever to the 1000 item as well so the remote lever can sit in there nicely. I am sort of torn between the two as being the original box I would like to keep it, though the 1000 would have better ratios and lets face it the original engine has long gone, it's been a 948 ever since I have owned it and even that has been replaced once.

I would like the later box as it would be nice to have better ratios and syncro all round, though I rather like the handbrake lever as the way it is supposed to be. Changing gears after chasing the gear lever about the passenger side of the car though would probably be something that I wouldn't miss too much as the lever currently flops about all over the place even when in gear, though it is easy and direct enough to use. It would be like driving a completely different car though I think, maybe it will all come down to availability of iems and their cost when the time comes.

I am though sorely tempted to get the reconditioned gearbox on e-bay though. Damn you e-bay!

I have to work out what I have done with the mechanism in the passenger side front door too as the locking jams up when the window is wound all the way up. This is a problem as unless you "waggle" the inside door handle the locking pin won't engage properly and as such the door is prone to opening iteslf when cornering, which can be a little disconcerting so the passenger. You could of course just wind down the window an inch or two and all is good, but it is not an acceptable situation. I must have put the thing back together the wrong way around, so I guess just a straight forward strip down and reinstall and see how it goes time will tell...     

MAR 2013

CB Radios

Who knew that things had moved on so far since I had the old AM unit in my first car. It was a flash jobbie for its day, Uniden with a main box and all other controls remote on the hand piece, so it could be installed all tucked away out of thieves line of sight. That of course moved on with that car and I “upgraded” to a single side band AM Electrophone beast that attached solidly somewhere always in sight and was a good reliable piece of kit, shame the sound quality was so awful as to make any incoming message almost impossible to understand. Mind you that one did make a progression through a variety of cars, actually it has even been in The Count on a previous occasion many years ago, well it was in there till I figured out it was for some reason providing a constant drain on the battery even when it was turned off. AM was the beast to have though, cheap and accessible, UHF was the new kid on the block and was expensive and no one had the damn things

I am now looking through all the information I can, thanks to Mr Google, and there sure seems to be quite a few changes in what is around, new legislations and laws and a whole lot of new channels available on UHF CB’s, now with 80 channels. Poor old AM seems to have taken the back seat, old tech and whilst still available, doesn’t seem to be popular any more like it once was. Seems you have to remember what all the channels are used for as otherwise you could get yourself into a bit of trouble. Oh and how’s that the manufactures have been given a stay of introduction so that they can go all out to try and sell the old 40 channel units to poor unsuspecting folk that may not have checked into things too carefully! Not that hard to research though so perhaps people need to pay attention a little.

So here I am now searching through the ACMA (Australian Media and Communication Authority) website looking at the new regulations and laws and at the ExplorOz and UHF CB Australia web sites to see what they recommend and what the new regulations actually mean in normal person language. I guess it all comes down to how much and what features you want on a unit, same as anything else a person wants to buy, and while there doesn’t appear to be that many manufacturers of UHF CB radios there seems to be a heck of a lot of models made by each of them. I am currently leaning towards the Oricom UHF180, though that is fairly much price driven. 

The research continues…….

And the winner is:

another Uniden - UH7700NB, tiny, takes next to no room, easy to fit and comes with an aerial, so we'll see how it goes.

FEB 2013

Well happy new year to everyone that may be reading this, if anyone at all is doing so, it’s late, but well you get that don’t you.

Things are progressing slowly and I have picked up the occasional part here and there for the car, so I should have everything I need by the time that I bring the car down from Queensland to Melbourne to get everything ready for the trip. I have been scrolling through all the part suppliers web sites both n the UK and over here and if I see something that is too good to pass up well I would be mad not to get it, wouldn’t I!

There are still lots of bits to get though and the good news is that I am going to be at the Beaulieu Auto Jumble, so hopefully I will be able to pick up a few items while there and hopefully I will be able to pack them into my luggage to get them home again too. Never had the opportunity to attend the Beaulieu meet before so really looking forward to seeing what it’s all about and what bargains may be there to be had, hopefully there will be heaps of bargains. Doesn’t hurt to hope does it?

I have been putting some time into thinking about how to wire all the extra accessories into the car too. I’m thinking that I may be able to route a relay into the start switch which will power an auxiliary fuse box and then have everything, including the starter will be powered through there. Well I am not an electronics whiz so not sure if I am way off track here or not, though there is a bit of time to think it out and get it right yet. Just happy that I have already converted it to an alternator rather than the old generator, I think it is going to be necessary.

I have to locate another parcel tray for the car to, in the move to get the car from Canberra to Queensland I lost a few parts, they have just disappeared, which is a bit disappointing as it includes the original parcel tray and the original steering wheel and steering column. So I have a mini column in the car at the moment and have a Mountney wood rimed wheel in it as well, as it just give so much extra space and at 6’3” that is a reasonable consideration I think.

I have been toying with the idea of replacing the gearbox with a 1000 one rather than the original Series II box which The Count is still running with. The thinking goes that I have to have the gearbox rebuilt or reconditioned anyway so for such a long trip why not get a box that will give me a better and more relaxed cruising speed (well ok that is the diff as well, but it has to be less noisy than the 803 box surely!). Though I am not sure I am warming to this, I have considered it many times before and have never acted on it as I just haven’t been able to get my head around “changing” the car, which I guess is silly given that it already has a 984cc in it (it had one when I got it and I wasn’t going to change it back), though other than poly suspension bushes and electronic ignition kit, Rover 1.3 Mini distributor, 74 Mini Clubman inlet manifold with associated carby and the heater out of same Clubman, it is as I got it way back when, so it is mostly original to me anyway, HA! Anyway changing the box would mean changing the transmission cover panel to the later 1000 one and also changing the handbrake lever over as well, and well that is the problem, I would actually see that difference and so would everyone else and it would be glaringly obvious. Silly I know, but there you go, I mean if its not broke then don’t fix it, perhaps. This one will require lots more thought and to be honest I would be surprised if I have come to a decision by the time I get back from the trip. Mind the having to recondition the box will probably have some sway to deciding before I go. Hmmm…….. watch this space!